How to Set a Static IP in Kali Linux Using the GUI and ifconfig?

Setting up a static IP for an Ubuntu machine can be a bit of a pain without the proper know-how, but it’s essential if you want to be able to connect to the Internet through your machine whenever you need to. Whether you need to connect to the Internet at home, over the public Internet using an ISP, or if you need to connect to the Internet that you’re sharing with another machine, creating a static IP is an essential step that should be taken before doing anything else.

Many people know that Linux is the best operating system for hackers. When they are learning how to hack, they often wish that they had a tool that they could use right out of the box to set a static IP. There are several ways to set a static IP on Linux, but the most common is using the ifconfig command. This article will explain how you can obtain your static IP with ifconfig, obtain your subnet mask with ifconfig, obtain the gateway with ifconfig, obtain the gateway’s subnet mask with ifconfig, obtain the hostname with ifconfig, obtain the hostname’s domain name with ifconfig, obtain the IPv6 address with ifconfig, obtain the IPv6 address’s prefix length with ifconfig, obtain

In this article I will show you how to setup your Kali Linux system to have a static IP address. The steps shown below will also work on other Linux distributions.

If you’re a Linux system administrator, you’ve almost certainly done the IP configuration. The procedure of configuring IP (static or dynamic) on Linux is frequently overlooked. And this is something that many people are scared about. In this post, I’ll show you how to set a static IP address in Kali Linux using the ifconfig command, both in the GUI and in the Terminal. So, without further ado, let’s get started.

How can I use the GUI to set up a static IP address in Kali Linux?

Step 1: Determine your router’s default gateway.

The first step is to determine the router’s default gateway; if you alter the default gateway, you will be unable to access to the network. In the Terminal, run the following command to discover the router’s Default Gateway.

ip r

The Default Gateway should be found.

Access Advanced Network Management in the second step.

To setup the static IP address, we must go to the advanced network administration settings. Right-click on the network connection and choose Edit Connections to go to the advanced network management options.

1630982847_164_How-to-Set-a-Static-IP-in-Kali-Linux-Using

In Kali Linux, you may change the network connection.

Choose WIred connection 1 under Ethernet, then click on the options at the bottom.

1630982847_779_How-to-Set-a-Static-IP-in-Kali-Linux-Using

Open the Options menu.

Step 3: Configure a Static IP Address

Go to the IPV4 category after the advanced network administration settings window is available. Change the mode from DHCP to Manual before entering the IP address, Netmask, and default Gateway. A green color indicates that they are accessible in the router; a red color indicates that they have been taken.

1630982848_912_How-to-Set-a-Static-IP-in-Kali-Linux-Using

Configure a Static IP Address

To apply the IP Address changes to the nettrok, you must restart Kali Linux after all of the modifications have been saved.

How do I set up a static IP address in Linux using the ifconfig command?

To set up a manual IP address and subnet mask on Kali Linux, open the terminal and enter the first command below. And, by the way, make sure the Terminal is running as root.

ifconfig eth0 192.168.1.2 netmask 255.255.255.0 sudo ifconfig eth0 192.168.1.2 netmask 255.255.255.0

Now we must configure the default gateway for the ethernet port stated above, which is Ethernet 0 with the IP address 192.168.1.2. To set the default gateway, use the following command.

sudo route add default gw 192.168.1.2 eth0 sudo route add default gw 192.168.1.2 eth0

Use the following command to setup DNS.

> /etc/resolv.conf echo “nameserver 1.1.1.1”

1630982848_394_How-to-Set-a-Static-IP-in-Kali-Linux-Using

Ifconfig is used to set up a static IP address.

Here are the commands that are used in the Terminal at the same time.

┌──(root💀kali)-[/home/kali] ifconfig eth0 192.168.1.2 netmask 255.255.255.0 sudo ifconfig eth0 192.168.1.2 netmask 255.255.255.0 ┌──(root💀kali)-[/home/kali] # sudo route add default gw 192.168.1.2 eth0 192.168.1.2 eth0 ┌──(root💀kali)-[/home/kali] # (rootkali)-[/home/kali] # (rootkali)- /etc/resolv.conf # echo “nameserver 1.1.1.1”

Remember that you must specify the following settings, which we have previously done, in order to set up a static IP.

  • DNS 1 and DNS 2 are two DNS servers.
  • Gateway
  • Hostname
  • NetMask
  • IPADDRESS

Now that you’ve completed all of the steps, check to see whether the static IP address is operational. To see whether it’s working, type ping google.com and hit enter.

If you see the notice below, it indicates you need to change your Static IP address.

  • ping: google.com: Temporary name resolution failure

If you see the notice below, it indicates everything is functioning well and you are ready to go.

(kalikali)-[] ping google.com PING google.com (kalikali)-[] ping google.com (kalikali)-[] ping google.com (kalikali)-[] ping google (142.250.181.14) There are 56(84) bytes of data. icmp seq=1 ttl=128 time=38.6 ms from fjr04s05-in-f14.1e100.net (142.250.181.14): 64 bytes icmp seq=2 ttl=128 time=38.5 ms from fjr04s05-in-f14.1e100.net (142.250.181.14): 64 bytes icmp seq=3 ttl=128 time=38.2 ms from fjr04s05-in-f14.1e100.net (142.250.181.14): 64 bytes C —- ping statistics from google.com —- rtt min/avg/max/mdev = 38.162/38.408/38.606/0.184 ms rtt min/avg/max/mdev = 38.162/38.408/38.606/0.184 ms rtt min/avg/max/mdev = 38.162/38.408/38.606/0.184 ms rtt min/avg

Conclusion

The first step in setting up a static IP in Kali Linux is to determine the router’s default gateway. Then go to the IPV4 tab in network administration and enter a static IP address. That concludes our tutorial on how to set up a static IP address in Kali Linux.

In this tutorial, I’ll show you how to set a static IP address on a Kali Linux system with a GUI interface.. Read more about how to change ip address in kali linux terminal and let us know what you think.

Frequently Asked Questions

How set static IP with ifconfig in Linux?

To set a static IP address in Linux, you can use the ifconfig command.

How do you change IP address in Kali Linux GUI?

You can change your IP address in Kali Linux by using the following command: ip addr show

How do I get the IP address of Ifconfig in Kali Linux?

Ifconfig is a command line tool that can be used to view the current configuration of your network interface. ip addr show Q: How do I get the IP address of ifconfig in Kali Linux? Ifconfig is a command line tool that can be used to view the current configuration of your network interface.

Related Tags

  • kali linux eth0 no ip address
  • kali linux configure network manually
  • how to change ip address in kali linux virtualbox
  • kali linux ip address command
  • linux set ip address static command line

Leave a Comment

Your email address will not be published. Required fields are marked *